Dotfiles: Best way to store in a bare git repository
Disclaimer: the title is slightly hyperbolic, there are other proven solutions to the problem. I do think the technique below is very elegant though.
Recently I read about this amazing technique in an Hacker News thread on people's solutions to store their dotfiles. User StreakyCobra
showed his elegant setup and ... It made so much sense! I am in the process of switching my own system to the same technique. The only pre-requisite is to install Git.
In his words the technique below requires:
No extra tooling, no symlinks, files are tracked on a version control system, you can use different branches for different computers, you can replicate you configuration easily on new installation.
The technique consists in storing a Git bare repository in a "side" folder (like $HOME/.cfg
or $HOME/.myconfig
) using a specially crafted alias so that commands are run against that repository and not the usual .git
local folder, which would interfere with any other Git repositories around.
Starting from scratch
If you haven't been tracking your configurations in a Git repository before, you can start using this technique easily with these lines:
git init --bare $HOME/.cfg
alias config='/usr/bin/git --git-dir=$HOME/.cfg/ --work-tree=$HOME'
config config --local status.showUntrackedFiles no
echo "alias config='/usr/bin/git --git-dir=$HOME/.cfg/ --work-tree=$HOME'" >> $HOME/.bashrc
- The first line creates a folder
~/.cfg
which is a Git bare repository that will track our files. - Then we create an alias
config
which we will use instead of the regulargit
when we want to interact with our configuration repository. - We set a flag - local to the repository - to hide files we are not explicitly tracking yet. This is so that when you type
config status
and other commands later, files you are not interested in tracking will not show up asuntracked
. - Also you can add the alias definition by hand to your
.bashrc
or use the the fourth line provided for convenience.
I packaged the above lines into a snippet up on Bitbucket and linked it from a short-url. So that you can set things up with:
related material
How to move a full Git repository
SEE SOLUTION
Learn Git with Bitbucket Cloud
curl -Lks http://bit.do/cfg-init | /bin/bash
After you've executed the setup any file within the $HOME
folder can be versioned with normal commands, replacing git
with your newly created config
alias, like:
config status
config add .vimrc
config commit -m "Add vimrc"
config add .bashrc
config commit -m "Add bashrc"
config push
Installing your dotfiles onto a new system (or migrate to this setup)
If you already store your configuration/dotfiles in a Git repository, on a new system you can migrate to this setup with the following steps:
- Prior to the installation make sure you have committed the alias to your
.bashrc
or.zsh
:
alias config='/usr/bin/git --git-dir=$HOME/.cfg/ --work-tree=$HOME'
- And that your source repository ignores the folder where you'll clone it, so that you don't create weird recursion problems:
echo ".cfg" >> .gitignore
- Now clone your dotfiles into a bare repository in a "dot" folder of your
$HOME
:
git clone --bare <git-repo-url> $HOME/.cfg
- Define the alias in the current shell scope:
alias config='/usr/bin/git --git-dir=$HOME/.cfg/ --work-tree=$HOME'
- Checkout the actual content from the bare repository to your
$HOME
:
config checkout
- The step above might fail with a message like:
error: The following untracked working tree files would be overwritten by checkout:
.bashrc
.gitignore
Please move or remove them before you can switch branches.
Aborting
This is because your $HOME
folder might already have some stock configuration files which would be overwritten by Git. The solution is simple: back up the files if you care about them, remove them if you don't care. I provide you with a possible rough shortcut to move all the offending files automatically to a backup folder:
mkdir -p .config-backup && \
config checkout 2>&1 | egrep "\s+\." | awk {'print $1'} | \
xargs -I{} mv {} .config-backup/{}
- Re-run the check out if you had problems:
config checkout
- Set the flag
showUntrackedFiles
tono
on this specific (local) repository:
config config --local status.showUntrackedFiles no
- You're done, from now on you can now type
config
commands to add and update your dotfiles:
config status
config add .vimrc
config commit -m "Add vimrc"
config add .bashrc
config commit -m "Add bashrc"
config push
Again as a shortcut not to have to remember all these steps on any new machine you want to setup, you can create a simple script, store it as Bitbucket snippet like I did, create a short url for it and call it like this:
curl -Lks http://bit.do/cfg-install | /bin/bash
For completeness this is what I ended up with (tested on many freshly minted Alpine Linux containers to test it out):
git clone --bare https://bitbucket.org/durdn/cfg.git $HOME/.cfg
function config {
/usr/bin/git --git-dir=$HOME/.cfg/ --work-tree=$HOME $@
}
mkdir -p .config-backup
config checkout
if [ $? = 0 ]; then
echo "Checked out config.";
else
echo "Backing up pre-existing dot files.";
config checkout 2>&1 | egrep "\s+\." | awk {'print $1'} | xargs -I{} mv {} .config-backup/{}
fi;
config checkout
config config status.showUntrackedFiles no
Wrapping up
I hope you find this technique useful to track your configuration. If you're curious, my dotfiles live here. Also please do stay connected by following @durdn or my awesome team at @atlassiandev.
Share this article
Next Topic
Recommended reading
Bookmark these resources to learn about types of DevOps teams, or for ongoing updates about DevOps at Atlassian.